If you are looking for high-quality products, please feel free to contact us and send an inquiry, email: brad@ihpa.net
Introduction to Zirconium Silicide Zi2 powder
Zirconium silicide
ZrSi2, or steel gray rhombic gloss crystal with chemical formula ZrSi2, has a relative density of 4.8822. Zirconium Silicide is not soluble or soluble with water, inorganic acid and aqua regia. It can however be dissolved in hydrofluoric.
Zirconium siicide ZrSi2 powder’s physicochemical properties
The zirconium silica intermetallic compound ZrSi2 (zirconium-silicon) is a ceramic material having high hardness, high melting temperature, high conductivity as well as high heat conductivity. ZrSi2 is an intermetallic silicon zirconium-silicon compound with superior chemical and physical properties. It can also be used as high-temperature corrosion medium.
You can make zirconium silicide by heating a mix of silicon and zirconium powder under high temperature isolation.
The following steps can be used to make zirconium silicide Nanomaterial.
1. In a 20ml stainless Steel autoclave, add 5mmol of zirconia, 5mmol silica powder, 50mmol lithium and seal it. Place the heated autoclave inside an electric furnace with temperature control. The furnace should heat at 600°C. Once the reaction cools to room temperature the autoclave will be open to get rid of the black sediment.
2. Following washing of reaction products with distilled water and then with dilute hydrochloric and anhydrous alcohol washing each time after washing, 60 were placed in the oven for drying four hours to get zirconium Silicide nanomaterials. This is based upon the quality of the zirconium oxide used and on the prepared zirconium nanomaterial quality.
Zirconium Silicide Zi2 powder
To make semiconductor film or crucibles, ZrSi2 is a good ceramic raw material.
Zr Zirconium can be used in various applications
The production of white pigment impervious agents and surface glaze pigments for ceramics and tiles is one of the main uses of zircon. The common uses of zircon are in refractory, such as the fabrication of firebricks or shapes for the steel and the glass industries. Because of its high melting temperature (2200 degrees), zircalite can be used for casting sand and grinding “flour,” especially for warmer areas where castings must maintain their quality. This is the area where zirconium has been used in increasing numbers. Also, zirconium can be used to produce zirconia and zirconium-based chemicals.
Hauptlieferant of Zirconium Silicide ZiSi2 Powder
Technology Co. Ltd. (), is a trusted supplier and manufacturer of global chemicals. We have more than 12 years experience providing high-quality chemical products, such as silicon powder, nitride, graphite, zinc sulfide, calcium nitride and 3D printing powder.
High-quality products are what you want zirconium silicide ZrSi2 dust Please feel free and contact us to send an enquiry. (brad@ihpa.net)
Zirconium siicide ZrSi2 powder’s physicochemical properties
The zirconium silica intermetallic compound ZrSi2 (zirconium-silicon) is a ceramic material having high hardness, high melting temperature, high conductivity as well as high heat conductivity. ZrSi2 is an intermetallic silicon zirconium-silicon compound with superior chemical and physical properties. It can also be used as high-temperature corrosion medium.
| Zirconium Silicide ZrSi2 Pulp Properties | |
| Additional Names | zirconium(IV) silicide, zirconium disilicide, ZrSi2 powder |
| No. | 12039-90-6 |
| Formula compound | ZrSi2 |
| Molecular Weight | 147.4 |
| Appearance | gray black powder |
| Melting Point | N/A |
| Boiling Point | N/A |
| Density | 4.88g/cm3 |
| Solubility in water | Unsolvable |
| Get the exact Mass | 145.858557 |
Zirconium Silicide ZrSi2 Puffer CAS 12039-90-6
Making Zirconium Silicide Zi2 powder
You can make zirconium silicide by heating a mix of silicon and zirconium powder under high temperature isolation.
The following steps can be used to make zirconium silicide Nanomaterial.
1. In a 20ml stainless Steel autoclave, add 5mmol of zirconia, 5mmol silica powder, 50mmol lithium and seal it. Place the heated autoclave inside an electric furnace with temperature control. The furnace should heat at 600°C. Once the reaction cools to room temperature the autoclave will be open to get rid of the black sediment.
2. Following washing of reaction products with distilled water and then with dilute hydrochloric and anhydrous alcohol washing each time after washing, 60 were placed in the oven for drying four hours to get zirconium Silicide nanomaterials. This is based upon the quality of the zirconium oxide used and on the prepared zirconium nanomaterial quality.
Zirconium Silicide Zi2 powder
To make semiconductor film or crucibles, ZrSi2 is a good ceramic raw material.
Zr Zirconium can be used in various applications
The production of white pigment impervious agents and surface glaze pigments for ceramics and tiles is one of the main uses of zircon. The common uses of zircon are in refractory, such as the fabrication of firebricks or shapes for the steel and the glass industries. Because of its high melting temperature (2200 degrees), zircalite can be used for casting sand and grinding “flour,” especially for warmer areas where castings must maintain their quality. This is the area where zirconium has been used in increasing numbers. Also, zirconium can be used to produce zirconia and zirconium-based chemicals.
Hauptlieferant of Zirconium Silicide ZiSi2 Powder
Technology Co. Ltd. (), is a trusted supplier and manufacturer of global chemicals. We have more than 12 years experience providing high-quality chemical products, such as silicon powder, nitride, graphite, zinc sulfide, calcium nitride and 3D printing powder.
High-quality products are what you want zirconium silicide ZrSi2 dust Please feel free and contact us to send an enquiry. (brad@ihpa.net)