Principle of optocoating:
Vacuum coating refers to coatings that must be done in higher vacuums, such as vacuum ion, magnetron, magnetron, molecular beam epitaxy and PLD laser-sputtering. A substrate is formed from the plated materials and electroplated material. The target and substrate are in the same vacuum.
The evaporation coating is usually the target of heating so that the surface components evaporate in the form of free radicals or ions and are deposited on the surface of the substrate by film-forming method (scattering island structure-trapezoidal structure-layered growth).
You can easily understand the process of forming a sputtered coat by the fact that electrons or high energy lasers bombard the target material and surface components are released as free radicals.
An optical film has a smooth top, a geometrically-segmented interface between layers, and a refractive Index that can jump at interfaces. But it’s continuous within the film.
The absorption medium can be either uniformly normal or not. Practical application of the film can be more difficult than an ideal one. Because of its optical and physical characteristics, it is different from bulk material. Its surface and interface are also rough which causes diffuse scattering. Due to mutual penetration, the films form a diffusion interface. The anisotropy is formed by the film’s growth, structure, and stress.
Common optical coating materials include the following:
1. Metal (alloy): germanium, chromium, aluminum, silver, gold, etc.
This rare metal is safe and non-radioactive. It has a light transmission range of 2000NM to 14000NM.
Sometimes found in spectroscopes, and often used as a “colloid” layer to enhance adhesion. It may range from 550 to 30NM. But, under the guidance of aluminum mirror, 30NM can be an effective value for adhesion.
It is the most reflective metal in the ultraviolet area. Effective thickness is over 50NM.
When the evaporation rate and substrate temperature are fast enough, silver will have the same high reflectivity of aluminum. This is because there is more absorption due to the massive accumulation that occurs at very low speed.
Material with highest reflectivity of all known materials is above infrared 100nm wavelength
By electron gun evaporation the property of the material changes with film thickness. The refractive index, which is approximately 1., can be used. 8 % at 500 nm. It’s very well-known as an aluminum protective coating, in particular due to its high incident angle at 800-12000nm.
High-density tungsten boat evaporates cerium dioxide on a substrate of 200°C to get a refractive Index of about 2.2. The absorption band is located at about 3000nm, and its refractive indice changes with temperature. Oxygen ion plating can produce nylon 2.35 (500nm), which is a low absorption thin film.
The refractive Index is defined as the light transmission range between 2.21500 and 3.15400nm. People love this material because of its high refractive and relative firmness. It is used for anti-reflection films, splitter films, cold light films, filter, high reflective film, glasses film and thermal mirror.
It is a transparent colorless crystal with a high melting point, hardness and chemical stability. Use it for high-quality Si02 coatings. It has a very pure crystal with no melting point. You can divide it into infrared, visible and ultraviolet depending on your use. A film that has too much pressure can cause pores to form and be fragile. Conversely, a film that has too little pressure will be absorbable and its refractive Index will rise.
High refractive index, high resistance to temperature and chemical stability make the white heavy crystal very pure. You can use it for high quality zirconia coatings. Because of its roughness, the incident light will be diffused and the transmittance of your lens is reduced. Additionally, optical rotation will cause certain incident light sources to dissipate particularly strongly. One example is that a material which absorbs red light appears green. But, poor processing can still be avoided.
If the substrate is heated to 150C by an electron gun, its refractiveindex is approximately 2.0C. Oxygen ion assisted plating can achieve a stable refractiveindex of 2.5-2.1. In the region of 8000-12000NM, HFO2 works better than SiO2 for the protective outer layer.
This antireflective coating has a 1×4 wave thickness and is used widely as an optical glass. It transmits about 120NM true ultraviolet radiation to the middle-infrared region at about 7000nm.
Calcium fluoride or barium fluoride.
The only problem with their compactness is that they are not completely solid. They can be used only in infrared films because transmittance shifts towards longer wavelengths at higher temperatures.
This material can also be used in UV. If it’s used in 300nm it will have a lower refractive value when it comes into direct contact with molybdenum or tantalum. Therefore, platinum and ceramic dishes are required.
4. Additional compounds
Light transmission ranges with refractive indices of 2.35400-13000m have good durability and stress. Mainly used to make spectroscopic and cold light films, decorative film, filters, high reflective film and infrared films.
It’s an IR material of high refractive. Because it’s a thin-film material, transparency is possible in between 300 and 4000 NM. The material is sublimated in the infrared. Substrat temperature is 250C. Prevention is essential. The maximum range of 40000NM is sufficient to make it work. Many other materials can be used to create a 14000NM edge.
Silicon dioxide Price
Price is affected by many things, such as the demand and supply in the market and industry trends. Economic activity. Unexpected events.
For the current SiO2 prices please send an inquiry. (firstname.lastname@example.org)
Silicon dioxide Supplier
Technology Co. Ltd. (), is a respected SiO2 provider , and SiO2 manufacturer . It has over twelve years’ experience. All of our products are available for shipment worldwide.
Feel free to email us for a high-quality siO2 powder. (email@example.com)